| Thursday, 29th April | ||||||
| Time | ||||||
| Thursday, 29.04 | 9:00 | Registration (Room VII - 226, Tallinn University of Technology, Ehitajate tee 5, Tallinn) and coffee | ||||
| 10:15 | Opening: Vice-Rector J.Kübarsepp | |||||
| 10:30 | Key-speaker: Chairman of Federation of Estonian Engineering Industries Dr J.Riives | |||||
| 11:00 | Key-speaker: Prof. T.Kjellberg | |||||
| 11:30 | Key-speaker: Prof. J.Papstel | |||||
| 12:00 | Lunch (in Dining Hall) | |||||
| 13:00 | Design Engineering (Room VI-121) | Production Engineering (Room VI-224) | Engineering Materials (Room V-408) | Production Management (Room VI-113) | ||
| Chair: Dr. A.Sulcs | Chair: Prof. V. Kauppinen | Chair: Prof. V.Mironov | Chair: Prof. R.Küttner | |||
| MSc, MIED M.Veveris | Prof. P.Kuosmanen | Dr. A.Laansoo | Dipl.-Kfm. H..Jähn | |||
| Prof. L.Roosimölder | Prof. J.Papstel | |||||
| Dr. E. Napalkov | ||||||
| 13:00 | Armada, M.; Beresnevich, V. & Tsyfansky, S. SUPPRESSION OF LATERAL OSCILLATIONS OF FLEXIBLE ELEMENTS IN MACHINES AND DEVICES | H. Annuka, H. Klaasen, J. Kübarsepp, V. Suvi Adhesive wear behaviour of carbide composites and tool steels | Ficko, M.; Pahole, I. & Drstvenek, I. WHAT MAKES AN EXPERT? | |||
| 13:20 | Canadija, M. & Brnic, J. APPLICATION OF FINITE ELEMENT METHOD IN THERMOMECHANICS | Antonov, M.; Hussainova, I. & Pirso, J. CHROMIUM CARBIDE BASED CERMETS AS THE WEAR RESISTANT MATERIALS | Janushevskis, A.; Akinfiev, T.; Auzins, J. & Boyko, A. VERIFICATION OF GLOBAL SEARCH PROCEDURE FOR RESPONSE SURFACE METHOD | |||
| 13:40 | Eerme, M.; Enok, M.; Roosimölder, L. Mass reduction of plate frames | Abiline, I; Laaneots, R & Nanits, M. CALIBRATION OF COATING THICKNESS GAUGES | Bolanča, I. & Bolanča, Z. CHEMICAL AND ENZYMATIC DEINKING FLOTATION OF DIGITAL PRINTS | Karaulova, T. & Papstel, J. SOFTWARE TOOLS FOR MODELLING AND SIMULATION OF MANUFACTURING PROCESSES | ||
| 14:00 | Gonca, V.; Grasmanis, B. & Viba, J. INVESTIGATION OF OBLIQUE IMPACT IN TRAFFIC ACCIDENTS | Aryassov, D., Otto, T., Gromova, S. ANALYSIS OF LATHE VIBRATION INFLUENCE ON BLANK ROUGHNESS | Cifanskis, S.; Armada, M.; Akinfiev, T.; Viba, J. & Jakushewich, V. HIGH VOLTAGE DISCHARGE SYSTEM FOR GRANULATING HARD MATERIALS | Küttner, R. Optimal planning of product mix for subcontracting companies | ||
| 14:20 | Grossschmidt, G.; Harf, M. SIMULATION OF STATICS AND STEADY STATE CONDITIONS OF AN ELECTRO-HYDRAULIC SERVO-SYSTEM | Barashkova, T. THE IMPORTANCE OF ORDER CORRELATION | Ilyuschenko, A.F., Okovity, V. A., Sobolevsky, S. B. Development of the concept of the plasma coating formation from partially stabilized zirconium dioxide and nickel cermet on the fuel cell element considering forecasting and their exploitation properties | Küttner, R., Kurg, J. OPTIMAL PLANNING OF TECHNOLOGICAL FOW LINES | ||
| 14:40 | Grossschmidt, G.; Harf, M. MULTI-POLE MODELING AND SIMULATION OF DYNAMICS OF AN ELECTRO-HYDRAULIC SERVO-SYSTEM | Budic, I.; Novoselovic, D. ;Skoric, S. PARAMETERS INFLUENCING WET TENSILE STRENGTH OF MOULDING MIXTURE | Ilyuschenko, A.F., Shevtsov, A.I., Okovity, V.A., Buikus, K.V. . Research of residual stresses in system "sprayed particle - substrate" | Shevtchenko, E. MRP SYSTEMS RESEARCH | ||
| 15:00 | Coffee break | |||||
| 15:20 | Heinloo, M & Olt, J. THE IMAGINATION OF THE FORCED DRIVEN DISK-RIDGING TOOL AND ITS WORKING PROCESS IN THE MATHCAD ENVIRONMENT | Karjust, K.; Papstel, J & Pohlak, M. KNOWLEDGE BASED SYSTEM OF THE SURFACE FINISHING PROCESSES | Kommel, L NEW ADVANCED TECHNOLOGIES FOR NANOCRYSTALLINE METALS MANUFACTURING | Lõun, K.; Tammoja, P. QUALITY FUNCTIONS AS KEY FACTORS FOR ORGANIZATION DEVELOPMENT | ||
| 15:40 | Kakko, A. & Reedik, V. On Reshaping of the Product Development Environment in Traditional Machinery Plant | Kauppinen, V. HIGH-SPEED MILLING - A NEW MANUFACTURING TECHNOLOGY | Kommel, L., Kimmari, E. RECYCLING OF LIGHT WEIGHT B4C BASED COMPOSITES | Stepanov, A. , Laansoo, A. Application of statistical methods in assessing the quality of welding | ||
| 16:00 | Kononova, O; Viba, J & Akinfiev,T. IMPACT SYSTEM RESTITUTION COEFFICIENT DEPENDENCE ON GEOMETRY | Pohlak, M.; Küttner, R.; Majak, J.; Karjust, K. & Sutt, A. EXPERIMENTAL STUDY OF INCREMENTAL FORMING OF SHEET METAL PRODUCTS | Kübarsepp, J., Vainola, V.,. Klaasen, H., Loel, R. BEHAVIOUR OF HARD ALLOYS IN SLIDING AND EROSION WEAR CONDITIONS | Zschorn, L.; Jähn, H. & Härtig, M. Factors influencing the Reliability of Delivery Promises in Case of Production | ||
| 16:20 | Küttner, R., Nekrassov, G. IMPLEMENTATION CBR SYSTEM FOR COMPUTER-AIDED DESIGN OF WORK-HOLDERS | Pohlak, M.; Küttner, R.; Majak, J.; Karjust, K. & Sutt, A. SIMULATION OF INCREMENTAL FORMING OF SHEET METAL PRODUCTS | Lille, H.; Kõo, J. & Ryabchikov, A. Measurement of Residual Stresses in the Coating Deposited by Brush-Plating on a Thin-Walled Short Cylinder | |||
| 16:40 | Lanc, D.; Turkalj, G. & Brnić, J. LINEAR STABILITY ANALYSIS OF SHEAR FLEXIBLE THIN-WALLED BEAMS | Sannik, U.; Pappel, T. COMPLETE MILLING TECHNOLOGIES OF DIFFERENT VALUABLE MATERIALS | Mikli. V., Kulu, P., Tarbe, R., Peetsalu, P. DOUBLE-CEMENTED RECYCLED HARDMETAL BASED POWDERS FOR THERMAL SPRAY | |||
| 17:00 | Mikkor, A., Roosimölder, L. Programmable Logic Controllers in Process Automation | Stopper, M. & Stuja, K. OPTIMIZING CYCLE TIME OF A flexible manufacturing cell USING SIMULATION SOFTWARE | Mironov, V.; Serdjuk, D. & Muktepavela, F. STEEL PROFILES FROM THE PERFORATED BANDS | |||
| 17:20 | Kulderknup, E., Laaneots, R., Raba, K. Modified calculation method of Tolerance of dimensional chain dependent link | Boķr, Ferenc Assembling Process Optimization for car industry | Mironov, V.; Viba, J. LIFTING OF FERROMAGNETIC POWDERS | |||
| 17:50 | Bus waiting | |||||
| 18:00-21:00 | Evening 'inn' session | |||||
| Friday, 30th April | ||||||
| Friday, 30.04 | 9:00 | Design Engineering (Room VI-121) | Production Engineering (Room VI-224) | Engineering Materials (Room V-408) | Production Management/INNOMET special (Room VI-113) | |
| 9:00 | Napalkov, E.; Zars, V MODELLING FUNCTIONALITY OF DESIGN PATTERNS BY MEANS OF FUZZY FRAMES | Sutt, A. ; Küttner, R. ; Pohlak, M. ; Karjust, K. DEVELOPMENT OF THE EXPERIMENTAL INTEGRATED DESIGN ENVIRONMENT FOR PROGRESSIVE CUTTING DIES | Ryabchikov, A. & Lille, H. Determination of residual stresses in galvanic coating from the measured longitudinal deformation of a tubular substrate | Jähn, H.; Zschorn, L. & Zimmermann, M. Monitoring the Social behaviour of participants in non-hierarchical production networks | ||
| 9:20 | Portyansky, L. GEOMETRICAL MODELLING TECHNIQUES TO DEVELOP A METAL STRUCTURE DESIGN SPACE | Widmaier, T.; Kuosmanen, P., Haikio, J. & Väänänen, P. A non-circular turning SYSTEM to minimise roll geometry errors | Saarna, M, Laansoo, A. Rail and rail weld testing | Larsson, M.; Kjellberg, T. HUMAN RESOURCE SKILL MANAGEMENT IN COMPANY NETWORKS | ||
| 9:40 | Resev, J. & Roosimölder, L. VIRTUAL DIFFERENTIAL AS TORQUE DISTRIBUTION CONTROL UNIT IN AUTOMOTIVE PROPULSION SYSTEMS | Zuperl, U. & Cus, F. ON-LINE CUTTING FORCE MODELLING FOR COPY ENDMILLS BASED ON MULTILAYER PERCEPTRON | čekaturovienė, D.; Viniakov, N. INFLUENCE OF TECNOLOGICAL STRESSES ON THE CORROSION OF WELDED PIPES | Luik, A. INNOVATION IN ESTONIAN ENTERPRISES. CHALLENGES AND TASKS FOR NATIONAL INNOVATION SYSTEM IN THE EUROPEAN RESEARCH AREA. | ||
| 10:00 | Seidla, A., Uusijärvi, R., DEVELOPMENT OF CODE-MARKING EQUIPMENT FOR LOGS SENSITIVITY OF FLUORESCENT CODE-MARK FOR LOG MARKING ENVIRONMENT | Oke, S.A. ROBOTICS: THE PAST, THE PRESENT, AND THE FUTURE | Viniakov, N., čekaturovienė, D.; Černaėjus, O. Modelling of Thermal Processes in a Dissymmetrical Welded Cast Aluminium Designs | Petković, D.; Visekruna, V.; Jasarevic, S & Plancic, I. TECHNOLOGY PARKS THE GENERATOR FOR DEVELOPMENT SME'S: ONE CASE FROM BOSNIA AND HEREZEGOVINA | ||
| 10:20 | Coffee break | |||||
| 10:40 | Sell, R. MECHATRONICS SYSTEM DESIGN IN CONCEPTUAL STAGE | Sen, M., Purohit, S.S., Shan, H.S. OPTIMIZATION OF MACHINING CONDITIONS IN ELECTRO JET DRILLING USING GENETIC ALGORITHM | Discussions | Riives, J.,Otto, T., Papstel, J. Monitoring of Technological Resources for Extended Usage | ||
| 11:00 | Sulcs, A. & Verners, O. DETERMINATION OF THE NONCENTROIDAL BODY BEHAVIOUR | Discussions | Riives, J., Papstel, J., Otto, T. POSSIBILITIES of the INNOMET system for HUMAN RESOURCES DEVELOPMENT IN ENTERPRISES | |||
| 11:20 | Sulcs, A. & Verners, O. VIBROTECHNOLOGICAL UNDERWATER CLEANING OF SHIP HULLS | Salopek, I.; Hudec, G. & Stracenski, M. THE ROLE OF WEB DESIGN IN PRODUCT PROMOTION AND EDUCATION | ||||
| 11:40 | Tars,P., Roosimölder, L. MODULARIZATION OF WASTE WATER PURIFICATION DEVICE | Discussions | ||||
| 12:00 | Lunch | |||||
| 13:00 | Teder, L. & Pappel, T. Detection of cavitation IN PUMPS through higher order derivatives | |||||
| 13:20 | Viba J., Polukoshko S. SIMULTANEOUS COLLISIONS OF RIGID BODIES IN MORE THAN ONE POINT | |||||
| 13:40 | Veveris, M. DESIGN FOR OBSOLESCENCE AND ECODESIGN A DICHOTOMY OR AN INNOVATION OPPORTUNITY? | |||||
| 14:00 | Vilnius, L.; Vekteris, V. & Čereka, A. MECHATRONICAL SYSTEM FOR TESTING OF HYDRODYNAMIC BEARINGS | |||||
| 14:20 | Tähemaa, T. TRENDS IN POSITIVE AND NEGATIVE SYNERGY AT MECHATRONIC SYSTEMS | |||||
| 14:40 | Discussions | |||||
| Free WiFi (Wireless Fidelity) connections are available in Dining Hall and Coffe Break facilities. | ||||||
| Wired LAN (Internet) connections for conference speakers are available at VI-121, VI-224 and VI-113. | ||||||
| All conference rooms are equipped with conventional overhead projectors, computers and video projectors. | ||||||